Magnetic Reed Door Switch
For use with all Sensaphone Dialers.
Detects any unauthorized entry or intrusion. Usually installed on doors and windows, the sensors monitor their opening and closing. Several magnetic reed switches may be wired in series.
Dimensions: 2.5" x 0.75" x 0.5" (part with screw terminals)2.5" x 0.75" x 0.625" (part with magnet)

Passive Infra-Red Motion Alarm
For use with all Sensaphone Dialers.
Monitors the movement of people in a specific area. Will cause a dialout if motion is detected. Range of detection covers approximately 50 ft. of area. Multiple sensors can be wired in series to a single input.
Dimensions: 4" x 6" x 1.5"

MiniAlarm Motion Sensor
For use with all Sensaphone Dialers.
Security motion sensor and siren for home or office security!
This compact motion sensor has a powerful 130 decibel siren and an alarm output signal that can be connected to any of the Sensaphone dialers. more info...
Dimensions: 2.75"x1.5" x 6.25"  Weight: 9ounces

Smoke Detector with Built-In Relay
For use with all Sensaphone Dialers.
This hard-wired photoelectric smoke detector is designed for residences and commercial buildings, including homes, apartments, hospitals, hotels and motels. It is engineered to virtually eliminate nuisance alarms and deliver outstanding performance wherever reliable fire protection is required. Built-in relay connects easily to any Sensaphone dialer. UL listed.

Smoke Detector with Built-In Relay and battery backup.
For use with all Sensaphone Dialers.
This hard-wired photoelectric smoke detector is designed for residences and commercial buildings, including homes, apartments, hospitals, hotels and motels. It is engineered to virtually eliminate nuisance alarms and deliver outstanding performance wherever reliable fire protection is required. A 9 VDC alkaline battery is provided for backup in the event building power is lost. Built-in relay connects easily to any Sensaphone dialer. UL listed.

Humidistat
For use with all Sensaphone Dialers.
Detects too high or too low humidity level. Range of the humidistat is 10% to 60% RH. The sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input. Dimensions: 4.125" x 2.75" x 1.5"

10K Immersion Temperature Sensor
Use with 1400,1800,2000 and Express II and SCADA 3000
Waterproof for measuring the temperature of fluids inside a pipe. 304 stainless steel probe. Brass WEL-B thermowell (screws into customer-supplied 0.5" NPT saddle or Thredolet® fitting in pipe). Fits into thermowell via brass 0.125" NPT fitting. Accurate to +/-0.36ºF (0.2ºC) with a sensing range of 10ºF to 230ºF. Includes 8' of 24AWG wire. Dimensions: Thermowell 5.125", Sensor in well 6.5"

Sump Bobber
For use with all Sensaphone Dialers.
DETECTS AND WARNS OF SUMP PUMP FAILURES! A simple float switch designed to monitor the water level in a sump pump well. Easily configured as a normally open or normally closed switch. Hose clamp allows easy level adjustment. more info...

Water Detection Sensor
For use with all Sensaphone Dialers.
Detects the presence of water on a horizontal surface. Independently powered by internal lithium batteries. Multiple sensors can be wired in series to a single input.
Dimensions: 2.25" x 1.125" x 3.625

WaterBug 200 Water Detection Sensor
For use with all Sensaphone Dialers.
Detects the presence of water on a horizontal or vertical surface. Up to 6 sensors may be added to the controller which is wired to an input of any Sensaphone Dialer. Requires 12 VDC power source. more info...

Water Rope Detection Sensor
For use with all Sensaphone Dialers.
Detects the presence of water via the attached water rope. It's Normally Closed output may be connected the the input of any Sensaphone Dialer. Powered by 2 AA batteries. Up to 10 lengths of water rope may be connected to create a rope with a maximum length of 100'. Additional Water Ropes are available.

Temp° Alert
For use with all Sensaphone Dialers.
Monitors air temperature from -30° to 130° F (-34° to 54° C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When temperature exceeds the setting, the sensor triggers an alarm. Can be mounted to any wall or vertical surface. Multiple Temp° Alerts may be wired in parallel to a single input.
Dimensions: 6.25" x 3.25" x 2"

GRT8800R Temperature Alarm
For use with all Sensaphone Dialers, or as a stand-alone monitor.
Monitors for high and low temperature violations. Perfect for coolers, freezers, refrigerators, food processing, storage, wine cellars, greenhouses and anywhere temperature monitoring is important. The GRT8800 relay output may be used to activate sirens, strobes or connected to any of Sensaphone telephone dialers. Complete with remote sensor! more info...
Dimensions: 5''W x 3.5''H x .75''D

GRH8800 Humidity Alarm
For use with all Sensaphone Dialers, or as a stand-alone monitor.
Monitors for high and low humidity violations. The GRH8800 relay output may be used to activate sirens, strobes or connected to any of Sensaphone telephone dialers.
Dimensions: 5''W x 3.5''H x .75''D

Humidity Transmitter
Use with 1400,1800,2000 and Express II and SCADA 3000
Space-mount, low-profile model has 10 point calibration accuracy and features a bulk polymer resistive sensor. 3% accuracy at 20 to 95% RH. Typical drift is less than 1% per year. The sensor output signal is field-selectable from 0-5 volt, 0-10 volt, or 4-20mA. Pre wired base makes installation easy.
For use with Sensaphone Models: 1400,1800,2000 and Express II and SCADA 3000.
Dimensions: 4.9" x 3.1" (12.4cm x 7.9cm)
Weight: 0.2 lb (0.9 kg)

FGD-0103: 10K Indoor Decorator Zone Temperature Sensor
Use with 1400,1800,2000 and Express II and SCADA 3000
Precision room temperature sensing in an attractive wall-mounted enclosure. Accurate to +/-0.36ºF (0.2ºC) with a sensing range of 35º to 140ºF. Beige plastic enclosure, tan metal faceplate
Dimensions: 4.5" x 3.23" x1.2"

Power-Out Alert™
For use with all Sensaphone Dialers.
A compact power outage monitoring device to protect against power outages. The Power-Out Alert easily plugs into any 110 VAC receptacle outlet for operation. Connect the SPST output alarm cable to your Sensaphone and prompt notification of the outage will occur after a fixed 3-8 minute delay. The delay guards against nuisance alarms. (All Sensaphones have built-in power monitoring, but this device may be used to monitor another building or service.)
Dimensions: 2.25" x 2" x 3" (5.7 cm x 5.1 cm x 7.6 cm)

FGD-0104: 10K Outdoor Air Weatherproof Temperature Sensor
Use with 1400,1800,2000 and Express II and SCADA 3000
Sensitive temperature element. Stainless steel tube sheathe. Mounted inside ventilated, treated weather-resistant PVC shield minimizing radiant energy effects. Mounted on a weatherproof outlet box for easy outdoor installation. Accurate to +/-0.36ºF (0.2ºC) with a sensing range of -30ºF to 140ºF. 8' of 24AWG wire included
Dimensions: 9" x3" x2"

Wireless Transmitter and 4 Zone receiver with 3000' range.
For use with all Sensaphone Dialers.
Wireless Transmitter and Receiver may be used to connect any contact sensor wirelessly. Transmitter accepts a Normally open or Normally closed contact input. Receiver has a 4 zone relay output that may be wired to 4 independent inputs of your Sensaphone or grouped together to one or more inputs. Program as many as 4 transmitters to one receiver for actual zone recognition on the dialer. Amazing 3000' range over open ground.

FGD-0010: Sensor and Accessory extension wire
2 conductor - 22 awg - white solid conductor wire. Ideal for connecting any of our sensaphone accessories to the sensaphone dialer. Available in pre-cut 50' or 100' length.

Phonecell® SX5E and SX5T Fixed Wireless Terminal
For use with all Sensaphone Dialers.
Provides proven, reliable access for your Sensaphone system where phone service is needed and cellular networks are available*. All of your communications requirements, such as voice, fax and data can be easily supported. The Phonecell gives you a full 3 watts of power for reliable signal strength. Simple RJ-11C interface. Compatible with all Sensaphone models! Dimensions: 9.7" x 7.2" x 1.7" (24.6 x 18.3 x 4.3 cm)
*Cellular service required through local cellular provider. more info..

Wireless Jack
Turns any AC outlet into a phone jack to which the Sensaphone may be connected. Avoids costly, time consuming, and difficult installations.

FGD-0300: Sensaphone 2000 Serial to Ethernet adapter

Allows you to connect your FGD2000 directly to an ethernet jack, enabling the ability to access the 2000 from any computer on the LAN or WAN.

Dual Thermostat
use with 400 Cottage Sitter
Eliminates the need to use two thermostats for the "setback" and "warm up" feature of the CottageSitter. This model features fan control and automatic heat cool switching. more info...

Dual Thermostat
use with 400 Cottage Sitter
Eliminates the need to use two thermostats for the "setback" and "warm up" feature of the CottageSitter. This model is used for furnaces with fan control and AC. more info...

Dual Heat Non- Programmable Thermostat
use with 400 Cottage Sitter

Eliminates the need for two thermostats to operate the "setback" and "warm-up" features of the Cottage Sitter. TH135 APPLICATIONS: Oil Burner, Natural Gas, Hot water heating, Hot air system with no fan control, no AC, Millivolts system, Electric heating with relay. more info...

7 Day Thermostat for Electric Heat
use with 400 Cottage Sitter

For use with the Cottage Sitter "setback" and "warm-up feature", eliminates the need for two thermostats. TH115 APPLICATIONS: Baseboards, Convectors, Radiant ceilings. more info...

240 Volt Relay
When wired across both phases of your electrical panel, this relay will create an alarm condition when either phase fails. Use with any Sensaphone® dialer.

International Power Option
This kit includes an international power adapter with 4 common plug types. For models FGD400 and FGD800 .

Various wire and burial cable for sensors, sirens, strobes, and most low voltage and security applications.
click for more information