Alarm Reviews and Advice Forum

Sensaphone 800 Alarm Dialer - Specifications

Alert Zones
Number of Zones:	8 (2.8K thermistor comes installed on zone 1 for temperature monitoring)
Zone Connector:	Terminal block
Zone Types:	N. O. / N. C. contact, 2.8K thermistor (-20° F to 150° F or -30° C to 65° C )
Zone Characteristics:	5.11K to 2.85V (Short circuit current: 1mA max.)
A/D Converter Resolution:	10 bits ±2 LSB
Zone Protection:	5.5VDC Metal Oxide Varistor with fast acting diode clamps.
Built in Microphone
Internal Electret Condenser:	For listening in to on-site sounds and detecting high sound levels.
Phone Interface
Line RJ11 Jack:	For connection to a two-wire analog telephone line. (6’ modular cord included)
Extension RJ11 Jack w/ Line Seizure:	For connecting other devices on the same telephone line, devices connected to this jack are disconnected in the event that the 800 must dial out for an alarm.
Phone Line Protection:	Metal Oxide Varistor & self-resetting fuse
LED Indicator
System On:	On steady when the unit is in RUN mode. LED blinks once every few seconds while in STANDBY mode.
Phone In Use:	On steady when the telephone line is being used. LED blinks when no dial tone is detected. Off when telephone line is not in use.
Alarm:	Off when no alarm exists. Blinks when an unacknowledged alarm exists. On steady when an acknowledged alarm exists
Battery Ok:	On steady when the battery is in good condition. Blinks when the battery is low. Off when the battery must be replaced.
Relay Output
Rating:	Rated for 1A 30VAC/1A 30VDC maximum.
Power Supply
Power Supply:	120VAC/9VDC 60Hz 6W wall plug-in transformer w/6’ cord.
Power Consumption:	1.5 Watts
Power Protection:	Metal Oxide Varistor
Battery Backup:	Six size-C alkaline batteries (not included), providing up to 24 hours of back-up time.
Environmental
Operating Temperature:	32–122° F (0–50° C)
Operating Humidity:	0–90% RH non-condensing
Storage Temperature:	32°–140° F (0–60° C)

Sensaphone 800 Alarm Dialer - Included

• 1 - Sensaphone 800 Alarm Dialer
• 1 - Power Adapter for Sensaphone Alarm Dialer
• 1 - 2.8K Thermistor hooked up to Zone 1 for temperature monitoring
• Manual
• Mounting Hardware
• 1 - 6 foot phone cord
• 1 - Phone Jack Extension for Line Seizure Feature

Sensaphone 800 Alarm Dialer

The Sensaphone 800 alarm dialer features four alarm inputs and will dial up to four phone number when an alarm condition is triggered. In addition to that you can call your alarm dialer at any time and listen to real time status reports of all sensors hooked up to your Sensaphone. This mean you could call in and get real time temperature readings, ensure that your motion sensors or door switches have not been tripped and even check for water leaks or power outages from anywhere in the world over the phone!

The Sensaphone alarm has a built in microphone which allows you to record your own alarm messages for each alarm zone so when the Sensaphone does call you with an alarm message you can hear your own voice telling you exactly where and what the alarm condition is! With all sorts of other programming options including alarm delay times, triggering your relay output to activate on alarm conditions or using the Sensaphone as a Cottage Sitter to heat up or cool down your home remotely the Sensaphone 800 alarm dialer is perfect for just about any residential alarm monitoring application!

Recordable Voice:

The Sensaphone 800 includes the ability to customize the voice messages for each of the input alarms and the identification message. The messages are recorded by the user through the built-in microphone. When the Sensaphone calls you with an alarm message you can hear your own voice telling you exactly what, where etc. the alarm condition is!

---

Output:

The Sensaphone 800 alarm dialers include a relay output that can be programmed to operate automatically upon alarm, or manually from a remote touch tone phone. It can be used to trip a local alarm, or used like the Sensaphone Cottage Sitter to control a dual setback thermostat.

---

Line Seizure:

Line seizure is a standard feature on the Sensaphone 800 alarm dialers.

---

Phone Line Monitoring:

 

There is a new phone circuit in the Sensaphone 800 alarm dialers that monitors the integrity of the phone line. If the phone line is cut or disconnected, an LED will flash and optionally the output relay can be tripped at the same time for a local indication of a problem.

---

Batteries:

The Sensaphone 800 alarm dialer has 24 hour battery backup capability using 6 C cell batteries (not included).

---

Phone Test:

Each dial out phone number can be tested from the keypad. When the test is being conducted, the speaker will play the sounds that are occurring on the real phone line. This makes is very easy to determine if the user needs to first dial a '9' or an '8' before the destination phone number, or other special dialing sequences.

---

LED's:

Additional status LED's are provided on the front of the Sensaphone 800 alarm dialer to show backup battery condition, alarm status, and phone status.

Sensaphone 800 Alarm Dialer - Support and Downloads

• Sensaphone Comparison Chart
• Sensaphone 800 Manual

Weather Proof Temperature Sensor Just: $27.00 USD Quantity:	Indoor Temperature Sensor Just: $19.00 USD Quantity:	Spot Water Sensor Just: $81.00 Quantity:
8 Zone Alarm Dialer Just: $535.50 USD Quantity:	4 Zone Alarm Dialer Just: $355.50 USD Quantity: